Whale Pressure Switch Mk2

$109.90

Whale Pressure Switch Mk2 (WU7207) — an in-line pressure switch that makes a non-automatic submersible or in-line pump automatic. Plumbed into the delivery line, it senses the pressure drop when a tap opens and starts the pump, then cuts it off at pressure (up to 2.6 bar / 30 PSI). 12V or 24V.

Genuine Whale (Navico). Supplied by Y3 Marine.

Add to Quote
SKU: 133471-BLA Category:

Description

Whale Pressure Switch Mk2

The Whale Pressure Switch Mk2 (WU7207) is a stand-alone in-line pressure switch that turns a basic, non-automatic pump into an automatic, pressurised freshwater system. It is plumbed into the delivery line between the pump and the taps: when any tap opens the line pressure drops, the switch senses it and starts the pump immediately; when the tap closes and pressure builds, it cuts the pump off. It is the simple way to get on-demand water from a pump that has no pressure switch of its own — a Whale submersible or in-line pump feeding one or two outlets (such as an Elegance faucet).

When to use it

Fit the Mk2 where you have a non-automatic submersible or in-line pump and want it to run automatically on demand rather than from a manual switch or microswitch tap. A pump that already has built-in automatic control (or a full pressure pump) does not need it. Maximum cut-off is 2.6 bar (30 PSI), for 12V or 24V Whale submersible / in-line pumps.

Specifications

Specification Detail
Type In-line pressure switch (stand-alone)
Function Starts a non-automatic pump on tap-open; cuts off at pressure
Max pressure 2.6 bar (30 PSI)
Voltage 12 / 24 V DC
Fits Whale non-automatic submersible & in-line pumps
Connection In-line barbed; adapters available for 15 mm Quick Connect / 1/2″ hose
Service kit AK7208 (microswitch, diaphragm, valve O-ring, valve)
Code WU7207

Dealer notes

  • Turns a basic pump automatic — the low-cost alternative to a full pressure pump for a one/two-outlet system off a submersible or in-line pump.
  • Needs the matching adapters for 15 mm Quick Connect or 1/2″ hose (sold separately) — confirm the fitting with the order.
  • Serviceable with kit AK7208; if the pump short-cycles, add an accumulator / surge dampener to smooth delivery.
  • Not for a pump that already has its own automatic control.

Fitting & service guide — in-line pressure switch

  1. De-power the pump and relieve system pressure before plumbing or wiring; confirm dead.
  2. Fit the switch in the delivery line after the pump, the correct way round (flow direction), using the adapters to match 15 mm Quick Connect or 1/2″ hose; support the hose and secure with stainless hose clamps.
  3. Wire it into the pump’s positive feed with marine-grade crimps and heat-shrink, joints above the waterline, on a fused feed.
  4. Test: open a tap — the pump should start promptly; close it — the pump should cut off at pressure. If it short-cycles, fit an accumulator / surge dampener. Service with AK7208 if it chatters or won’t cut off.

Genuine Whale (Navico). Supplied by Y3 Marine.

Additional information

Type

In-line pressure switch (stand-alone)

Function

Starts a non-automatic pump on demand; cuts off at pressure

Max Pressure

2.6 bar (30 PSI)

Voltage

12 / 24 V DC

Fits

Whale non-automatic submersible & in-line pumps

Connection

In-line barbed · adapters for 15 mm QC / 1/2" hose

Service Kit

AK7208

Code

WU7207

Brand

Whale (Navico)