Whale Orca Bilge Pump

Price range: $73.90 through $189.90

Whale Orca Bilge Pump — a compact, high-output submersible bilge pump with a wide, anti-clog intake and fuel-resistant ABS body. Switched models from 1,920 LPH to 4,920 LPH in 12V or 24V, run from a float switch, electronic field sensor or 3-way panel. Meets ISO 8849; 3-year warranty.

Genuine Whale (Navico). Supplied by Y3 Marine.

Add to Quote
SKU: N/A Category:

Description

Whale Orca Bilge Pump

The Whale Orca is Whale’s core electric submersible bilge pump: compact, efficient and built to keep shifting water where debris would choke lesser pumps. A large-footprint intake exposes the maximum area to bilge water and resists clogging, while the fuel-resistant ABS housing shrugs off the oil and diesel film typical of a working bilge. Every model in this listing is a switched pump — it runs from an external float switch, electronic field sensor or 3-way bilge panel.

For a self-contained pump that senses water and switches itself, see the Whale Orca Smart automatic range. For a slim pump that fits shallow or restricted bilges, see the Whale Supersub.

Configuration Options

Capacity Open flow Volts Current Fuse Hose Code
500 GPH 32 L/min (1,920 LPH) 12V 1.5A 2A 19mm (3/4″) BE0500
950 GPH 59 L/min (3,540 LPH) 12V 3.5A 5A 25/28.5mm (1″/1-1/8″) BE0950
1300 GPH 82 L/min (4,920 LPH) 12V 5.0A 7A 25/28.5mm (1″/1-1/8″) BE1450
1300 GPH 82 L/min (4,920 LPH) 24V 2.5A 5A 25/28.5mm (1″/1-1/8″) BE1454

Maximum discharge head: 3 m (500), 3.5 m (950), 4.5 m (1300). Flow at 1 m head is roughly 450, 850 and 1,100 GPH respectively.

Whale Build Quality

  • Meets ISO 8849 — the marine standard for electrically driven bilge pumps; CE certified
  • Fuel-resistant ABS body — withstands the oil, diesel and chemical film found in a working bilge
  • Wide, free-flowing intake — large surface area resists clogging and keeps flow up as the bilge empties
  • Easy-release cover — press both buttons and pull; the motor cartridge and filter area clean out without tools
  • Multiple wire-exit locations — the lead can be routed to suit a tight or awkward install
  • Low amp draw — easy on the battery for long unattended periods
  • Marine-grade internals — ABS body, Nitrile seals and Acetal impeller for a long service life in salt water
  • 3-year warranty on the 500–1300 models

Switched vs Automatic

A switched Orca does exactly what its control tells it: wire it to a float switch, a Whale electronic field sensor (BE9002/BE9003) or a 3-way panel and it runs on demand, with a manual override at the helm if you panel-wire it. That makes it the flexible choice where you already run a bilge panel, want a single switch to cover a high- and low-water pump, or prefer to keep the sensing separate from the pump. Where you want the pump to look after itself with no external switch, choose the Orca Smart instead.

Installation Notes

  • Mount as low as practical in the bilge sump — the lower the pump sits, the less residual water remains after each cycle.
  • Keep the strainer intake clear of frames and limber holes, with clearance around the base so debris can’t blank it off.
  • Run the discharge hose with a continuous upward slope to the overboard fitting; any low point forms an air lock that stops the pump priming after shutdown.
  • Fit a vented loop above the waterline on the discharge to prevent back-siphon / down-flooding through the overboard skin fitting.
  • Fuse the positive at the battery end at the rated size, and keep all wiring joints above the waterline.
  • Use the correct wire gauge for the run length to avoid voltage drop reducing output.
  • These pumps tolerate short dry running but should not be run dry continuously.

Nuisance water, MARPOL & oily-water discharge

These electric pumps are nuisance-water pumps. Their job is to keep the bilge dry during normal operation — clearing the everyday accumulation of rainwater, deck washdown, spray, condensation and shaft-gland or packing drips. They are not an emergency dewatering system for a holed or flooding hull; that role belongs to the manual Gusher range and to fixed emergency pumps sized to the vessel.

Because a bilge pump discharges whatever is in the bilge overboard, oily-water law applies. Under MARPOL Annex I — given effect in Australia by the Protection of the Sea (Prevention of Pollution from Ships) Act 1983 and enforced by AMSA — it is an offence to discharge bilge water containing oil above the permitted limit. Larger vessels must pass machinery-space bilge water through an approved oily-water separator to below 15 ppm oil, and never discharge in a port or a designated special area. Smaller craft without a separator must hold oily bilge water and land it ashore — it must not be pumped over the side. A visible diesel or oil sheen in the bilge means overboard discharge is illegal. Keep machinery-space bilges clean and oil-free, and where contamination is possible route the bilge to a holding tank or separator rather than straight overboard. This matters most with automatic pumps, which can discharge unattended — a bilge-water alarm and a clean bilge are the dealer’s standing advice.

Test it monthly

A bilge pump that fails quietly is only discovered when it is finally needed. Test every bilge pump and its switch or sensor at least monthly: lift the float or trigger the electronic sensor, confirm the pump actually runs and moves water, and check that the strainer is clear, the non-return/check valve seats, and the discharge line runs freely with no air lock. Confirm the automatic models cut in and cut out on their own. Keep a spare strainer base and a service kit aboard so a blocked intake or tired diaphragm can be put right on the spot.

Dealer notes

  • Switched pumps — pair each with a float switch, electronic field sensor or bilge panel; for hands-off operation choose the Orca Smart.
  • Fuse per Whale’s rating: 2A (500), 5A (950), 7A (1300 12V), 5A (1300 24V) — don’t over-fuse.
  • Match the stepped port to your hose and support the discharge each side to avoid strain on the body.
  • Keep a spare strainer base aboard; a blocked intake is the most common cause of “pump won’t keep up”.

Genuine Whale (Navico). Supplied by Y3 Marine.

Additional information

Capacity / Type

500 GPH · 12V, 950 GPH · 12V, 1300 GPH · 12V, 1300 GPH · 24V

Brand

Whale (Navico)

Type

Submersible bilge pump (switched)