SEPAR SWK-2000/40 Replacement Filter Element

Price range: $150.23 through $506.00

Lead time: please allow approximately 10 days for standard items and 4–10 weeks for non-standard / built-to-order configurations. Contact Y3 Marine to confirm the lead time for your item.

Genuine SEPAR replacement filter element for the SWK-2000/40 (2,400 LPH) fuel filter / water separator. Available in 10 micron (fine), 30 micron (standard), and 60 micron stainless steel. Backflushable up to 5 times.

Add to Quote
SKU: N/A Category:

Description

Genuine SEPAR replacement filter element for the SWK-2000/40 (2,400 LPH model). The SWK-2000 filter element provides the final stage (stage 5) of the 5-stage separation process, polishing fuel after centrifugal pre-separation has already removed the bulk of water and heavy particulate. Because of this pre-separation, the element stays clean far longer than a conventional inline primary filter element — and when restriction increases, it can be backflushed up to 5 times using the bleed screw procedure before replacement is required.

Element Options

Micron Rating Part Number Description
10 micron — fine 04010 Fine filtration for contaminated fuel supplies or injector-sensitive engines; shorter service interval than 30 micron
30 micron — standard 04030 General-purpose marine diesel filtration; pre-installed as standard in all SWK-2000 units; best service life in normal operation
60 micron — stainless steel 04060S Heavy-duty stainless steel element; longest service interval; suited to clean, well-managed fuel tanks where the centrifugal stages handle most of the contamination load

When to Replace

Replace the element on the engine manufacturer’s scheduled service interval, regardless of visual appearance. If the vessel is equipped with a restriction gauge (standard on SWK-2000/130; optional on other models), replace the element when the gauge indicates restriction even after backflushing. In a duplex installation, stagger element replacement between the two heads so one element is always fresh. Do not continue operating the engine with a blocked or severely restricted element — lift pump damage and fuel starvation will follow.

Backflush Procedure

SEPAR elements can be backflushed up to 5 times before replacement, extending service life significantly compared to a conventional inline filter element.

  1. Close the upstream ball valve to shut off fuel supply to the filter
  2. Open the bleed screw on the filter lid one full turn
  3. Allow fuel to backflush through the element for approximately 30 seconds, or until the flow from the bleed screw runs clean and free of debris
  4. Close the bleed screw and reopen the upstream ball valve
  5. Prime the fuel system before restarting the engine

If backflushing no longer restores flow (restriction indicator returns quickly after backflush), the element has reached the end of its serviceable life and must be replaced. Replace immediately — do not run the engine with a blocked element.

Element Replacement

  • Shut off fuel supply before opening the filter — close the upstream ball valve; if no ball valve is fitted, close the tank outlet cock
  • In a duplex system — switch the changeover lever to route fuel through the standby unit before servicing the active unit; do not open an active SEPAR head under fuel flow
  • Remove the bowl — the bowl unscrews or unbolts from the head depending on model; have a container ready to catch residual fuel
  • Replace the element — discard the old element responsibly as hydrocarbon waste; fit the new element; ensure it seats correctly against the element O-ring in the head
  • Inspect the bowl gasket / O-ring — replace if compressed, cracked, or deformed; do not refit a damaged bowl seal
  • Refit the bowl — hand-tighten only; do not use tools; over-tightening damages the polycarbonate bowl or the bowl thread
  • Prime and check for leaks — open the fuel supply, prime using the engine lift pump, start the engine, and inspect for leaks at the bowl joint before leaving unattended

Additional information

Micron Rating

10 micron — fine (Part No. 04010), 30 micron — standard (Part No. 04030), 60 micron — stainless steel (Part No. 04060S)

Fits Model

SWK-2000/40 (2,400 LPH model)

Standard Element

30 micron (Part No. 04030) — pre-installed in all SWK-2000 units

Fine Element

10 micron (Part No. 04010)

Heavy Duty Element

60 micron stainless steel (Part No. 04060S)

Max Backflush Cycles

5 — backflush using bleed screw procedure before replacing

Brand

SEPAR