Rule Standard Bilge Pump — Non-Automatic DA Series (1,360–4,160 LPH)

Price range: $68.00 through $191.00

Rule Next Generation DA Series non-automatic submersible bilge pumps, 360 to 4,160 LPH. Ignition-protected water/air-cooled motor, snap-on strainer base, stainless shaft, 3-year warranty. Requires a Rule float switch for automatic operation.

Add to Quote
SKU: N/A Category:

Description

Rule’s standard-range submersible bilge pumps deliver reliable bilge management for vessels from small runabouts to large yachts. The Next Generation DA Series features ignition-protected, water/air-cooled motors, moisture-tight wiring, stainless steel shaft, and snap-on strainer bases for easy cleaning and servicing. All models require a Rule float switch for automatic operation.

The compact round-base housing suits tight bilge installations. Available in 360, 500, 800, and 4,160 LPH capacities in both 12V and 24V (except 1,360 LPH which is 12V only). Backed by Rule’s 3-year limited warranty.

Specifications by model

Model Flow (open) Voltage Current draw
1,360 LPH (RWB800) 23 LPM 12V 2.3 A
1,890 LPH (RWB801) 31 LPM 12V 1.6 A
1,890 LPH (RWB802) 31 LPM 24V 0.8 A
3,030 LPH (RWB803) 50 LPM 12V 3.0 A
3,030 LPH (RWB804) 50 LPM 24V 1.5 A
4,160 LPH (RWB805) 69 LPM 12V 3.8 A
4,160 LPH (RWB806) 69 LPM 24V 2.0 A

Nuisance water, MARPOL & oily-water discharge

These electric pumps are nuisance-water pumps. Their job is to keep the bilge dry in normal service — clearing the everyday accumulation of rainwater, deck washdown, spray, condensation and shaft-gland or packing drips. They are not an emergency dewatering system for a holed or flooding hull; that role belongs to a manual bilge pump and to fixed emergency pumps sized to the vessel.

Because a bilge pump discharges whatever is in the bilge overboard, oily-water law applies. Under MARPOL Annex I — given effect in Australia by the Protection of the Sea (Prevention of Pollution from Ships) Act 1983 and enforced by AMSA — it is an offence to discharge bilge water containing oil above the permitted limit. Larger vessels must pass machinery-space bilge water through an approved oily-water separator to below 15 ppm oil, and never discharge in a port or a designated special area. Smaller craft without a separator must hold oily bilge water and land it ashore — it must not be pumped over the side. A visible diesel or oil sheen in the bilge means overboard discharge is illegal. Keep machinery-space bilges clean and oil-free, and route the bilge to a holding tank or separator where contamination is possible — this matters most with automatic pumps, which can discharge unattended.

Test it monthly

A bilge pump that fails quietly is only discovered when it is finally needed. Test every bilge pump and its switch or sensor at least monthly: lift the float or trigger the sensor, confirm the pump actually runs and moves water, and check that the strainer is clear, the non-return/check valve seats, and the discharge line runs freely with no air lock. Confirm any automatic model cuts in and out on its own. Keep a spare strainer base and service kit aboard so a blocked intake can be put right on the spot.

Dealer notes

  • Non-automatic — needs a float switch or a panel’s AUTO leg to run on its own; on its own it’s manual-only.
  • Size by flow & hull. 360 for small tenders up to 1100 for a cabin bilge; step up to the High-Capacity range above that.
  • Snap-on strainer base lifts the pump for cleaning without touching the plumbing — keep a spare base on the shelf.
  • Fuse and cable to the plate and avoid voltage drop on long runs — it kills flow.

Additional information

Configuration

360 — 1,360 LPH — 12V, 500 — 1,890 LPH — 12V, 500 — 1,890 LPH — 24V, 800 — 3,030 LPH — 12V, 800 — 3,030 LPH — 24V, 1100 — 4,160 LPH — 12V, 1100 — 4,160 LPH — 24V

Pump Type

Non-automatic — pair with float switch or 3-way panel

Range

1,360–4,160 LPH (360–1,100 GPH) — 12V & 24V

Discharge

Threaded port with check valve — 3/4" to 1-1/8" by model

Current / Fuse

~1.5–4.0 A / 3–7.5 A (by model)

Protection

Ignition protected · Thermal cut-out · EMC suppression

Construction

Stainless steel shaft · Teflon seals · Snap-on strainer base

Warranty

3 years — Rule limited warranty

Brand

Rule (Xylem)