Description
The Johnson Pump Aqua Void is a compact submersible bilge pump built around a removable cartridge — the motor and impeller lift out of the strainer base as one unit, so the pump can be cleaned or replaced in seconds without touching the base or the plumbed discharge. Available in 1,900 / 3,030 LPH (500 / 800 GPH), 12 V DC, with a water-cooled motor and a 316 stainless shaft for long, corrosion-free service.
Performance
| Model | Flow (open) | Port | Dimensions (W×H×L) | Current / fuse |
|---|---|---|---|---|
| Aqua Void 500 | 1,900 LPH (500 GPH) | 3⁄4″ Dura-Port | 70 × 119 × 133 mm | per data sheet |
| Aqua Void 800 | 3,030 LPH (800 GPH) | 3⁄4″ Dura-Port | 70 × 119 × 133 mm | per data sheet |
Choosing the right capacity
Bilge-pump ratings are open-flow figures (ISO 8849 / ABYC H-22); installed output is always lower once you add static head, hose length, elbows and the check valve. Size on the volume of nuisance water you expect, with margin — 500 GPH suits tenders and small craft or secondary/backup duty, 800 GPH covers larger cockpits and deeper bilges.
Cartridge design — service in seconds
The base and strainer stay installed and hose-connected; the motor cartridge twist-locks in and out. That means you can clear a jammed impeller or swap a failed pump afloat without cutting hose or removing fixings — and a spare cartridge turns a dead bilge pump into a two-minute fix. The kit includes straight and 90° smooth Dura-Port elbows and a removable check valve.
Nuisance water, not damage control
The Aqua Void is a compact intermittent-duty pump for rain, spray, shaft-gland weep and washdown — not a means of dewatering a holed hull. Emergency dewatering is the job of a dedicated engine-driven or portable crash pump, and on commercial and survey vessels it falls under AMSA / NSCV bilge-pumping requirements. Fit the Aqua Void as one layer of the bilge system, and control it with a float switch or panel (it is a non-automatic pump).
Key features
- Removable cartridge — motor/impeller lifts out of the base for tool-free service
- 1,900 / 3,030 LPH (500 / 800 GPH), 12 V DC
- Water-cooled motor; 316 stainless steel shaft
- 3⁄4″ Dura-Port discharge (straight & 90° elbows) and removable check valve included
- 16 GA tinned lead; compact 70 × 119 × 133 mm body
- Non-automatic — pair with a float switch or panel
MARPOL & oily-water discharge
A bilge pump discharges whatever is in the bilge overboard, so oily-water law applies. Under MARPOL Annex I — given effect in Australia by the Protection of the Sea (Prevention of Pollution from Ships) Act 1983 and enforced by AMSA — it is an offence to discharge bilge water containing oil above the permitted limit. Larger vessels must pass machinery-space bilge water through an approved oily-water separator to below 15 ppm and never discharge in a port or a special area; smaller craft without a separator must hold oily bilge water and land it ashore. A visible oil or diesel sheen means overboard discharge is illegal — keep the bilge clean and oil-free and route to a holding tank or separator where contamination is possible. This matters most with automatic pumps, which can discharge unattended.
Test it monthly
A bilge pump that fails quietly is only found when it is finally needed. Test every bilge pump and its switch or sensor at least monthly: raise the water level or trigger the float/sensor, confirm the pump runs and moves water, and check that the strainer basket is clear, the check valve seats, and the discharge runs freely with no air lock. Confirm any automatic model cuts in and out on its own, and keep a spare strainer basket and service kit aboard.
Dealer notes
- Non-automatic — pair with a float switch or 3-way panel; for a built-in switch see the Ultima range.
- The removable cartridge is the selling point — keep a spare cartridge aboard and a dead pump is a two-minute fix afloat.
- Water-cooled motor — never run dry; keep the strainer clear and test the pump and switch monthly.
- 500 suits tenders and backup duty; 800 for larger cockpits and deeper bilges.
Do not run dry. The water-cooled motor relies on the water it pumps for cooling — extended dry running will overheat and damage it.
Johnson Pump Marine by SPX FLOW. Supplied by Y3 Marine. Open-flow ratings (ISO 8849); confirm current draw and fusing against the Johnson data sheet for the model.





