Jabsco Run-Dry DC Macerator Pump

Price range: $488.00 through $515.00

Jabsco run-dry electric macerator pump with patented dry-run protection. 46 LPM open flow / 38 LPM @ 3m head. 4-blade S/S chopper. Triple-sealed ignition-protected motor. Empties a 120L holding tank in 3 minutes. 38mm inlet, 25mm outlet. 12V and 24V.

Add to Quote
SKU: N/A Category:

Description

Jabsco DC Macerator Pump — Run-Dry Waste Pump

The Jabsco run-dry DC macerator pump empties a black-water holding tank — grinding the waste through a stainless cutter and pumping it overboard or to a dockside pump-out. Its stand-out feature is patented dry-run protection: because a macerator keeps running as the tank empties, the seal of an ordinary macerator burns out when it sucks air — this one tolerates running dry, so it survives the normal pump-down. It delivers 46 L/min open flow (38 L/min @ 3 m head) through a 4-blade stainless chopper and will empty a ~120 L tank in about three minutes. Triple-sealed, ignition-protected motor; 12 V and 24 V.

Specifications

Spec Value
Flow 46 L/min open · 38 L/min @ 3 m head
Empties ~120 L holding tank in ~3 min
Cutter 4-blade stainless — reduces solids to ~3 mm
Inlet 1½” (38 mm) hose barb over a 1½” NPT male thread
Outlet 1″ (25 mm) hose barb
Priming Self-priming (~1.5 m) · run-dry tolerant
Motor Triple-sealed · ignition-protected · 12 / 24 V
Duty Intermittent (~15 min)

What it’s for — emptying a holding tank

The macerator draws from the black-water holding tank (or a macerating toilet) and discharges it one of two ways:

  • Overboard — macerated and pumped straight out through a skin fitting, where discharge is legally permitted.
  • To a dockside pump-out — pumped up to a deck pump-out fitting for shore reception.

The run-dry seal is what makes it reliable here: the tank will run empty mid-cycle, and that is exactly when a standard macerator fails.

⚠️ Discharge is regulated — read before plumbing overboard

Discharging untreated black water overboard is restricted by law — MARPOL Annex IV internationally, plus national and local rules and no-discharge zones. In many waters you may only discharge a set distance offshore (or not at all), and inside marinas, harbours and protected areas you must pump out to shore. Always plumb the system so waste can go to a holding tank / deck pump-out, and only fit and use the overboard path where it is legal to do so. Check the rules for your waters and flag state before relying on overboard discharge. This is general guidance, not legal advice.

Selecting overboard or pump-out — fit a diverter valve

To choose between the two discharge routes from one pump, fit a Jabsco Y-Valve waste diverter (45490-1000) on the discharge: one lever sends flow overboard or to the deck pump-out. The Y-Valve ships with 1½” ports and an extra 1″ (25 mm) barbed port that matches this pump’s 1″ outlet. Two caveats: make sure the diverter is rated for the macerator’s discharge pressure, and fit a vented loop above the waterline on the overboard leg to stop back-siphon.

Port & plumbing mechanics

  • Inlet — 1½” (38 mm): a moulded hose barb stepped over a 1½” NPT male thread. You have two options: push 38 mm bore sanitation hose over the barb and double-clamp it; or, to screw on a threaded fitting (hose tail, adapter or valve), cut the moulded barb back to the thread and thread on a 1½” NPT male fitting. (Jabsco ports are NPT — use an NPT fitting, or an NPT–BSP adapter if your plumbing is BSP.)
  • Outlet — 1″ (25 mm): a 1″ hose barb — run 25 mm bore discharge hose, double-clamped, up to a vented loop and then to the skin fitting or diverter.
  • Use proper sanitation hose throughout to avoid odour permeation, and keep the discharge run as short and straight as practical.

Installation & dealer notes

  • Mount above / beside the tank so it self-primes and drains back; keep the suction short.
  • Vented loop on the discharge, above the waterline — mandatory on an overboard leg to prevent back-siphon / down-flooding.
  • Run-dry tolerant, but switch it off once the tank is empty — don’t leave it running.
  • Intermittent duty (~15 min) — it’s a pump-out pump, not a continuous-duty pump.
  • Choose 12 V (J11-111) or 24 V (J11-110) to match the house bank.

Common faults

  • Runs but won’t clear: air-locked or blocked discharge, or a dull/jammed cutter.
  • Lost prime / weak flow: suction air leak or a blocked inlet.
  • Won’t restart after sitting: dried waste around the cutter — flush the system through after each pump-out.

Key features

  • Patented run-dry protection — survives the normal tank pump-down
  • 46 L/min open; empties ~120 L in ~3 min
  • 4-blade stainless chopper; triple-sealed, ignition-protected motor
  • 1½” NPT/barb inlet · 1″ barb outlet
  • Overboard or dockside pump-out — pair with a Jabsco Y-Valve diverter
  • 12 V and 24 V

Genuine Jabsco (Xylem). Supplied by Y3 Marine.

Additional information

Configuration

12V, 24V

Type

DC waste macerator pump — run-dry

Flow

46 L/min open · 38 L/min @ 3 m

Empties

~120 L tank in ~3 min

Cutter

4-blade stainless — solids to ~3 mm

Inlet

1½" (38 mm) barb over 1½" NPT male thread

Outlet

1" (25 mm) hose barb

Priming

Self-priming ~1.5 m · run-dry tolerant

Motor

Triple-sealed · ignition-protected

Duty

Intermittent (~15 min)

Discharge

Overboard (where legal) or dockside pump-out · pair with Jabsco Y-Valve diverter

Voltage

12 / 24 V (by option)

Brand

Jabsco (Xylem)