Description
The CJC® Filter Separator PTU2 27/27 PVM keeps fuel and water-prone oils clean and dry on a continuous offline kidney loop. It pairs coalescer water separation with CJC depth-filter fine filtration, at higher flow than the 15/25, and adds a magnetically-coupled pump and a flexible control box for marine and industrial duty.
When You Need a Separator (Not Just a Fine Filter)
CJC removes water two ways: by absorption (the HDU Fine Filter soaks it into the insert) or by separation (the PTU coalesces and drains it). The PTU2 27/27 is the separator — for fluids carrying continuous or bulk free water that would saturate an absorption filter: diesel fuel (water settles out of every bunker) and oil systems with a water source. Where the oil is a clean, closed system with only condensation, an HDU Fine Filter is the simpler answer; where there is real water, the PTU earns its place.
How It Works
A CJC magnetically-coupled gear-wheel pump draws the fluid through the filter insert; from the centre of the insert it flows into the coalescer/filter base, where water droplets adhere to the coalescer element, merge into larger drops and settle to the bottom — drained off manually or automatically — while clean, dry oil leaves from the top. The depth-filter insert removes particles to 3 µm absolute and adsorbs varnish and oxidation by-products. Pressure drop across the insert (its contaminant loading) is shown on the filter-top pressure gauge. Being offline, it runs 24/7, even during shutdown, and inserts are changed without stopping the system.
Two Versions — Choose by Fluid
- Diesel — diesel fuels / light distillates, with a Type F / FA insert (low flow) or BLAT (high flow).
- Hydraulic — hydraulic, turbine-lube and gear oils (with good demulsibility), with a Type BLAT insert.
Diesel: Clean, Dry Fuel — and No Diesel Bug
On the diesel version the pump draws from the bottom of the settling/bunker tank (above the drain tap) and delivers clean, dry fuel to the service tank, with an overflow line returning surplus to settling. It strips the free water that settles out of every bunker, plus particles and degradation products — which means high-quality clean & dry diesel, no bacterial “diesel bug” growth in the tanks, reduced wear on injectors and fuel pumps, and fewer system breakdowns. Ideal as a transfer-and-polish unit on service and settling/bulk tanks.
Water-Contaminated Oil Systems (Hydraulic)
The hydraulic version runs as a kidney loop on the oil tank — drawing from the bottom and returning near the main-pump suction at a non-pressurised point — to strip water and contamination from hydraulic, turbine and gear oils that see a water source: leaking coolers, washdown, or the seawater ingress typical of stern tubes and thruster gears. It protects bearings, valves, gears and servo components from the water that destroys oil additives and drives corrosion and cavitation.
Filtration Performance
- Water removal by coalescer separation to very low levels (efficiency depends on oil type and temperature)
- Particle removal: 3 µm absolute (98.7% of particles >3 µm; 50% of >0.8 µm per pass)
- Adsorbs oxidation products, resin/sludge and varnish
- Dirt-holding capacity ~4 L
- CJC depth-filter inserts in cellulose / cotton linters depending on fluid
The Control Box
The flexible control box adds automatic water discharge, motor control and protection, and high-pressure detection, and can be delivered with a 3 m power cable so it mounts remotely from the filter housing. The unit is also available with no control box and manual water discharge.
Why Offline Filtration Pays on a Yacht
Continuous offline filtration extends oil and component life 2–10× — fewer oil changes, so less waste oil to store and land (limited tankage, costly disposal, MARPOL Annex I), less downtime, and protected, hard-to-access components. The PTU is Lloyd’s Register type approved (PTU2 27) for classed vessels.
Technical Data
| Diesel | Hydraulic | |
|---|---|---|
| Fluids | Diesel / light distillates | Hydraulic, turbine lube, gear |
| Filter insert | Type F / FA or BLAT | Type BLAT |
| Pump | Magnetically-coupled gear (PVM) | Magnetically-coupled gear (PVM) |
| Pump flow | 90–300 L/h | 90–300 L/h |
| Pump inlet pressure, max | 10 bar | 10 bar |
| Power consumption | 0.18 kW | 0.18 kW |
| Max oil temperature | 60 °C | 60 °C |
| Design pressure | 7 bar | 7 bar |
| Dirt holding | ~4 L | ~4 L |
| Weight (dry / wet) | 76 / 90 kg | 76 / 90 kg |
| Water discharge | Manual or automatic | Manual or automatic |
Electric motor in all standard AC and DC voltages. Options: control box (no/flexible), pressure switch, drip pan, heater.
Flow rate & sizing
The PTU2 27/27 runs at ~150–450 L/h depending on the pump fitted. This table breaks that range into representative flow options and the system oil volume each suits — sized to your oil volume, not the machine. Keep-clean figures assume ~3 turnovers a day; polishing a dirty or wet charge needs more turnovers, so the same flow suits a smaller volume (or a longer run). Exact pump is confirmed at quote.
| Pump flow rate | Oil processed / 24 h | Keeps a system clean (~3 turnovers/day) |
Polishes a charge (~7 turnovers/day) |
|---|---|---|---|
| 150 L/h | ~3,600 L | up to ~1,200 L | up to ~510 L |
| 300 L/h | ~7,200 L | up to ~2,400 L | up to ~1,030 L |
| 450 L/h | ~10,800 L | up to ~3,600 L | up to ~1,540 L |
How to size a CJC — the turnover rule
An offline filter cleans only a fraction of the contamination on each pass, so cleanliness builds up over repeated turnovers of the whole charge. Size the unit against your system oil volume, not the machine it sits on:
- Keep-clean (maintenance): size so the entire oil volume passes through ~3× every 24 hours. Run it continuously — even at rest.
- Clean-up / polishing: for a dirty or wet charge, run continuously until on-target — expect the full volume to pass ~7× to reach target cleanliness / dryness.
- Removing water: water leaves gradually, so keep polishing until below target (gear oils typically <200 ppm, ideally <100 ppm) and fix the ingress source.
Worked example: a 500 L gearbox at ~110 L/h turns the full charge over about every 4.5 hours — roughly 5× a day, comfortably in the maintenance band. Polishing that same charge from wet or dirty (~7 turnovers) takes about 32 hours of continuous running.
Selecting & Installing
Choose the version by fluid and size the unit to the system — for fuel, to the engine’s consumption rate for continuous day-tank polishing on service/settling tanks; for oil, to the reservoir volume. Y3 Marine will specify the version, insert, control-box option and installation to suit your vessel — send us the fluid, the system volume or engine consumption, and the supply voltage.





